婷婷在线视频,亚洲二区在线视频,日本免费在线观看视频,精品一区视频,亚洲男人的天堂在线,国产国语对白一级毛片,欧美艳照

Hello, welcome to the official website ofTaizhou Tongjiang Washing Machinery Factory!
Service hotline
13305263777
13921703632
keywords:Industrial washing machine industrial dehydrator industrial dryer industrial ironing
新聞中心

One of the common problems of industrial washing machines is that the water in washing machines is not smooth

發(fā)布:1 瀏覽:1281次

Industrial washing machine often encountered a problem is: washing machine water is not smooth, there will be no water or water does not stop, when encountered these problems how to solve? We give the following solutions. 1. Check whether the drain valve of the industrial washing machine is blocked by dirt, which may cause the water inflow of the industrial washing machine is not smooth. Solution: clean the dirt inside the drain valve in time. 2. Check whether the computer board is damaged or aged. Solution: replace the new computer board or re adjust the computer program. When the washing machine does not water: check whether the water inlet valve filter screen is blocked and whether the water inlet valve is damaged? After confirming that they are in good condition, measure the voltage of 220 V at both ends of the solenoid valve with the AC voltage block of the multimeter, proving that the fault is in the solenoid valve itself. When measuring the resistance of solenoid valve coil with resistance block, the normal value should be 4.5 ~ 5.1k & and the measured resistance value is infinite, which indicates that the coil of solenoid valve is burnt out, replace the water inlet valve and remove the fault. Industrial washing machine water inflow: the water inflow of the washing machine has reached the rated water level, and the water inlet solenoid valve still does not stop. In this case, the water level pressure switch is damaged, which can be judged by blowing pressure method. Cut off the power supply; remove the water level switch, blow air to the pressure switch through the return pipe, and measure the resistance between the two terminals of the water level switch with a multimeter. When blowing, the resistance should tend to zero, and when not blowing, the resistance value should be greater than 10k & after inspection, the measured resistance value of the machine is always very large, and the action sound of the contact in the water level switch can not be heard, which indicates that the water level pressure switch is faulty. After replacing the water level pressure switch, the fault was eliminated. Fault location of drainage failure: drain valve is blocked; electromagnet coil is open circuit; program controller has no signal output. The above is what we give you to the industrial washing machine water is not unobstructed.

Contacts:Chen Yingchun Mobile:13305263777 13921703632 (Same number of mobile wechat)

Tel:0523-86552777,86552888 Fax:0523-86588830 E-mail:manager@tzcyc.com

Add:28 Xingfeng East Road, Hailing District, Taizhou City, Jiangsu Province

copyright:Taizhou Tongjiang Washing Machinery Factory 【Disclaimer】

惠水县| 资中县| 秭归县| 巴林右旗| 玛纳斯县| 连江县| 扬中市| 海原县| 班玛县| 海晏县| 南部县| 滕州市| 潜江市| 和政县| 临洮县| 县级市| 长垣县| 康平县| 高阳县| 屏东县| 新平| 太仆寺旗| 平原县| 湘潭市| 胶州市| 绥芬河市| 武清区| 铜山县| 闵行区| 松桃| 丰台区| 黑山县| 绥宁县| 昆山市| 鄂托克前旗| 阿鲁科尔沁旗| 承德县| 凤庆县| 凤台县| 宁城县| 乌兰察布市|